Quiver Killer Mounting Screw Set
Sales price £12.00
Description
A full set of mounting screws made from top quality A2 (304) DIN 965Z/7985Z stainless steel. All have no.2 pozidrive heads so to avoid damaging the heads a no.2 pozidrive screwdriver must be used. A spare screw will be included for each head style/length of screw within each set. Some bindings required the head diameters &/or lengths of the standard screws to be reduced and if that is the case with the binding you select then the alterations will be done free of charge for you by Jon.
See below for a list of the Quiver Killer mounting scrww sets available for the most popular makes/models of binding. So simply order the number of screw sets you require but then please state the make(s)/model(s) of your binding(s) that you require the screws for in the Customers Notes box on the bottom of the order check-out page.
IMPORTANT NOTICE REGARDING THE USE OF LOCTITE
Loctite is very harmful to some of the plastics of which bindings are composed and if it comes in to contact with such the plastic will fail within a short period of time and without any signs of there being an issue.
For this reason Quiver Killer only certifies the use Vibra-TITE VC-3 threadlock which is a non-anaerobic formula that is benign to all plastics. This is first painted onto the end 4/6mm of the mounting screws & left to dry (which only takes a few minutes) before the screws are either installed or stored. The screws may be un- and re-installed several times before a new coating is required.
For this reason Quiver Killer only certifies the use Vibra-TITE VC-3 threadlock which is a non-anaerobic formula that is benign to all plastics. This is first painted onto the end 4/6mm of the mounting screws & left to dry (which only takes a few minutes) before the screws are either installed or stored. The screws may be un- and re-installed several times before a new coating is required.
Quiver Killer Mounting Screw Sets:
B&D Ski Gear telemark ski crampon mounting bracket
Vist Free, Performance or Race
CAST Freetour (Pivot 15/18)
Look Pivot 12/14 GW (19/20 onwards)
Look Pivot 12/14 Dual alpine/GripWalk (18/19)
Look Pivot 12/14 Dual alpine/WTR (16/17 & 17/18)
Look Pivot 14 (up to 15/16)
Look Pivot 18 GW (19/20 onwards)
Look Pivot 18 WTR
Look Pivot 18 Alpine (without 4mm toe lifter)
Look Pivot 18 Alpine (with 4mm toe lifter)
Look PX12/14
Look PX12/14 Race
Look SPX 12 GW
Look SPX 12 Dual alpine/GripWalk & (18/19 onwards)
Look SPX 12 Dual alpine/WTR (16/17 & 17/18)
Look SPX12
Look NX12
Marker Comp 12 (2024), 12 GW & Comp 10 TCX
Marker 11 TP & 12 TCX
Marker Duke PT 16 & 12
Marker Alpinist 8/9/12
Marker Kingpin 10/13 & Kingpin MWerks 12
Marker Kingpin Demo
Marker Jester, Jester Pro, Squire with ID or MN AFD & Squire 11 (GW)
Marker Jester, Griffon or Squire (H18mm AFD's & H10 x L200mm heel base plate)
Marker Jester Pro 18, Jester, Griffon or Squire (H21mm AFD's & H13 x L240mm heel base plate)
Marker Free Ten ID
Marker Free Ten
Marker Lord SP14
Marker Schizo
Marker Duke or Baron (up to 2009/10)
Marker Duke & Baron (2010/11 & after inc EPF)
Marker F10 Tour & F12 Tour (inc EPF)
Marker 14.0 Free
Marker Griffon Demo (up to 2009/10)
Marker Griffon Demo (2010/11 to 2015/16)
Marker Griffon Demo (2016/17 onwards)
KneeBinding Carbon & Shadow
KneeBinding Mist, Core & Hardcore
Head Mojo (from 2011/12)
Head Mojo (up to & inc 2010/11):
Note that the two rear holes in the metal chassis of the heel pieces on these bindings are undersized which makes it difficult for the new screws to remain vertical during insertion which then causes alignment problems with the inserts. It is therefore recommended to run a 5.5mm or 7/32" drill through these holes prior to using the new screws.
Head Ambition
Head Adrenalin – note that Quiver Killer inserts are not compatible with this binding
Head Attack 13
Head Attack 13 Demo
Tyrolia Attack2 14 AT
Tyrolia Attack2 13 AT Demo
Tyrolia Attack2 13 GW, 16 GW & Attack 14 GW:
Note that the two rear holes in the metal chassis of the heel pieces on these bindings are undersized which makes it difficult for the new screws to remain vertical during insertion which then causes alignment problems with the inserts. It is therefore recommended to run a 5.5mm or 7/32" drill through these holes prior to using the new screws.
Fischer X13
Fischer X17
Tyrolia Peak 11 TH & Peak 12
Tyrolia Peak 15
Tyrolia Peak 18
Tyrolia Storm (non diagonal release heel)
Tyrolia Storm (diagonal release heel)
Rossignol Freeski 2 140XL
Rossignol Freeski 150 or 180
Rossignol Axial 3 WTR
Rossignol Axial 3
Rossignol Axial 3 Rental
Rossignol Axium
Rossignol Axium Pivot (original semi-pivot version)
Salomon MTN (without brakes) & Atomic Backland Pure
Salomon MTN (with brakes) & Atomic Backland Tour
Salomon Guardian/Atomic Tracker/Look XM
Salomon Shift MNC 13 & 10
Salomon Shift2 13 & 10 Multinorm
Salomon Strive 12 & 14
Salomon Strive 16 MN
Salomon Strive Demo
Salomon Warden 11 MNC
Salomon Warden 13 MNC
Salomon Warden 13 MNC Demo
Salomon STH2 WTR
Salomon STH14 Driver/Atomic FFG14 Driver /Atomic FFG16 Driver
Salomon STH12/Atomic Team Ltd Edition
Salomon Z12ti
Salomon Z10/Z12/Atomic FFG12
Salomon 914 Driver
Salomon S912ti with lifter
Salomon Z12/Scott S12 rental
Salomon S810
Salomon L7 Demo Plate
Salomon X16
Plum Guide
Plum Guide with wide bases
Plum Guide with brake
Plum Yak
Dynafit Beast 16
Dynafit Beast 14
Dynafit Beast 14 Test
Dynafit Radical 2 ST/FT & Rotation
Dynafit Radical 2 ST Test
Dynafit Speed Turn/Speed Turn 2.0/Speed Radical
Dynafit Superlite 2
Dynafit Superlite 2 heel shift plates only
Dynafit Radical ST & FT
Dynafit TLT Speed
Dynafit TLT Vertical ST
Dynafit Vertical FT & FT12
ATK Raider 11/13/15 Evo (2024 onwards with metal heel base) without 4mm toe shim
ATK Raider 11/13/15 Evo (2024 onwards with metal heel base) with 4mm toe shim
ATK Raider 11/13/15 Evo (up to 2023 with plastic heel base) without 4mm toe shim
ATK Raider 11/13/15 Evo (up to 2023 with plastic heel base) with 4mm toe shim
ATK Freeraider 14 & Raider 12
ATK C-Raider 12
ATK Crest 10 (2024 onwards)
ATK Crest AP (2023)
ATK Crest 8 & 10 (up to 2023)
ATK Rent Me 12 (with heel brake)
ATK Haute Route 10
ATK Raider 12 2.0 (with toe brake)
ATK Front 10) with toe brake)
ATK FR14 2.0 (with toe brake)
ATK Raider 12 2.0
Kreuzspitze GT
Black Diamond 01
Voile Switchback/Switchback X2
G3 Ion (with pan head heel screws)
G3 Ion (with csk flat head heel screws)
G3 Onyx
G3 Targa
G3 Targa Ascent
22 Designs Hammerheads
22 Designs AXL/Outlaws/Vice
M Equipement Meidjo
M Equipement Meidjo 2.0
M Equipement Meidjo 2.1
M Equipement Meidjo 2.0 tech heel only
M Equipment Meidjo 3
Fritschi Vipec (1st & 2nd gen)
Fritschi Evo/Tecton/Vipec Black/Xenic
Fritschi Eagle
Frtischi Scout
Fritschi Freeride
Fritschi Freeride Plus
Fritschi Explorer
Fritschi Freeride Pro
Fritschi Experience
Fritschi Titanal
Rottefella NTN Freeride (up to & inc 11/12)
Rottefella NTN Freeride (from 12/13)
Rottefella NTN Freedom
Rottefella BC Manual
Rottefella NIS Bases
7tm Garmont Tour
7tm Power Tour
Naxo NX21
Silvretta 400
Silvretta 404
Dynaduke Plates (Plates to skis)
Vist WCAEX14N Race Plates (Plates to skis)
Vist Speedlock Pro Superlight Plates (Plates to skis)
Vist Demo Plates (Plates to skis)
IMPORTANT NOTICE REGARDING THE USE OF LOCTITE
Loctite may be harmful to some of the plastics of which bindings are composed. For example, 22 Designs specifically forbids the use of Loctite with their telemark bindings.
For this reason Quiver Killer only recommend the use Vibra-TITE VC-3 which is a non-anaerobic formula that is benign to all plastics. This is first painted onto the end 4/6mm of the mounting screws & left to dry before installation. The screws may be removed and re-installed several times before a new coating is required.
Login Form
Shopping cart
Cart empty